Sveba Dahlen
I62 Rack Oven

5 Year Heat Exchanger Guarantee!

Gas fired four rack oven platform style
BCS touch screen control panel
Control panel can be operated both manually or is programmable up to 99 recipes.
Four single rack or two double rack capacity
Standard platform turning system with two separate drive belts.
Unit approved for zero (0) clearance to combustible surface sides and rear.
Standard Type II baking canopy. 1000 CFM minimum
All stainless steel construction
Rock wool mineral insulation throughout
“Patented” IBS rotation system
Increased baking surface, rack rotation is alternately clockwise and counter-clockwise for uniform baking
Electronic solft start rack rotation
Gentler bake with high volume and low velocity air movement via two variable speed fans
Patented cascade steam system (works without nozzles) with steel balls and aluminum rods
Flush front design
Heat exchanger completely in stainless steel
Oven door to have two (2) double glazed windowpanes, inner pane heat reflecting. Outer pane will be top hinged to open outwards with two (2) fluorescent light bulbs for interior lighting located behind outer pane.
Controls are recessed and protected
Oven door to have two (2) double glazed windowpanes, inner pane heat reflecting. Outer pane will be top hinged to open outwards with two (2) fluorescent light bulbs for interior lighting located behind outer pane
Door latch design completely in stainless steel material and with double lock cylinders
Inside door handle release, recessed hinges and safety switches
Adjustable air slots
Automatic damper

Shipping Weight 9,000 lb
Width 114.75 in
Depth 94.5 in
Maximum Rot. Diameter 75.75 in
Maximum Tray Size (Single Rack) 4 x 23.6 x 31.5 in
Maximum Tray Size (Double Rack) 2 x 18 x 20 in
Dough Per Bake 616 lb
Output 600000 Btu/hr
Voltage (Connection 1) 120 V
Phase (Connection 1) 1
Frequency (Connection 1) 60 Hz
Branch Circuit Current (Connection 1) 15 A
Voltage (Connection 2) 208 to 240 V
Phase (Connection 2) 3
Frequency (Connection 2) 60 Hz
Branch Circuit Current (Connection 2) 15 A
Water Connection NPT 3/8 in
Water Drain Damper Connection (NPT) 3/8 NPT or 3/4 NPT (front right drain only) in
Automatic Overpressure Damper Diameter 6.3 in
Hood Connection Diameter1 8.6 in
Supply Air, Evacuation Steam 5.1 in
Flue Gas Connection Diameter 10 in
Gas Connection (NPT) 1-1/4 in

Available Options

Prison package
460/480 Volts
Water pressure regulator and filter
Door/exhaust fan interlock

Combustion chamber exhaust: Type “B” vent
Baking chamber exhaust/Automatic damper connection (120 CVM)
Draft inducer is provided to maintain proper draft during burner operation
Draft inducer (shipped separate) must be installed in combustion stack above draft diverter. Installation by hvac contractor
Important: Use only Tjerlund D-3 inducer!
Sensing port of draft inducer must be connected to sensing port of proving switch (located in electrical cabinet) with 1/4″ aluminum tubing (supplied).
Draft inducer motor must be wired to relay and neutral in oven electrical cabinet. Wiring materials by others. Wiring according to local and national codes.
Check over-fire drafts and adjust to negative: .01 to .02 inches W.C. using fire chamber sight glass port during burner operation.

Type:Natural gas (Propane optional)
Power input:600,000 Btu/h – Natural gas (Propane)
Supply pressure:5.5 – 14.00″ wc Natural gas (Propane)
Connection:Refer to Midco burner manual for proper maintenance, adjustments and operating instructions

1/2″ drain connection
3/8″ water line @ 50/80 PSI water pressure
Water pressure regulator and water filter recommended (but not supplied)

Interested in this product or need more information?

Contact a Regional Sales Rep

Sveba DahlenI62 Rack Oven

Sveba Dahlen
I62 Rack Oven